OPTIMALISASI PENGGUNAAN SUPERPLASTICIZER MASTERGLENIUM ACE 8595 DALAM IMPLEMENTASI PEKERJAAN BETON

Mahendra Septa Kuswiantoro; Zendy Bima Mahardana; Ma’rifatul Mumayyizah; Alfina Iskindaria; Rifqi Sahrul Nurhuda; Farikhatul Mufaidah; Moch Risjad Aldiansyah

doi:10.36341/racic.v9i1.4128

Mahendra Septa Kuswiantoro Kadiri University
Zendy Bima Mahardana Universitas Kadiri
Ma’rifatul Mumayyizah Universitas Kadiri
Alfina Iskindaria Universitas Kadiri
Rifqi Sahrul Nurhuda Universitas Kadiri
Farikhatul Mufaidah Universitas Kadiri
Moch Risjad Aldiansyah Universitas Kadiri

: https://doi.org/10.36341/racic.v9i1.4128

Abstract

Technological advances in the construction world are growing rapidly, including the development of materials and construction methods. The use of superplasticizer additives in the manufacture of concrete can increase compressive strength and viscosity in achieving the workability of concrete cast work. Itis necessary to optimize the proportion of the use of superplasticizer additives to achieve the best workability. This study aims to determine the best workability in the use of concrete mixture superplasticizer admixture. The additive used is MasterGlenium ACE 8595 with a percentage of use of 0.25%, 0.28%, 0.31%, and 0.34%. The results revealed that the best workability was obtained in the addition of admixture of 0.31% of the weight of cement with a slump value of 14 cm and a compressive strength value of 17.35 Mpa which indicates that concrete is suitable for use in non-structural elements such as cyclope, pavement and masonry bare concrete. Through these results, it is hoped that it can be used as a reference to find the best workability from the use of MasterGlenium ACE 8595 superplasticizer for the implementation of appropriate construction.

Keywords: Workability, MasterGlenium ACE 8595, Concrete

References

Achmad, D. and Supriyan, D. (2019) ‘Studi Pendahuluan Batas Maksimum Kadar Lumpur Pada Agregat Beton Geopolimer’, Jurnal Poli-Teknologi, 18(1), pp. 19–28. Available at: https://doi.org/10.32722/pt.v18i1.1283.

Ahmad, A. et al. (2021) ‘Comparative study of supervised machine learning algorithms for predicting the compressive strength of concrete at high temperature’, Materials, 14(15). Available at: https://doi.org/10.3390/ma14154222.

Alsadey, S. and Mohamed, S. (2020) ‘Evaluation of the superplasticizer effect on the workability and strength of concrete’, International Journal of Engineering & Technology (Ijet), 9(1). Available at: https://doi.org/https://doi.org/10.14419/ijet.v9i1.29909.

Amelia, R., Suhendra, S. and Amalia, K.R. (2021) ‘Hubungan Faktor-Faktor yang Mempengaruhi Kuat Tekan Beton’, Jurnal Talenta Sipil, 4(2), p. 225. Available at: https://doi.org/10.33087/talentasipil.v4i2.79.

ASTM-C117 (2013) ‘ASTM C117-13 Standard Test Method for Materials Finer than 75-µm (No . 200) Sieve in Mineral Aggregates by Washing’, ASTM International, (200), pp. 1–3. Available at: https://doi.org/10.1520/C0117-17.

ASTM-C143 (1990) ‘Standard Method for Slump of Hydraulic-Cement concrete’.

ASTM-C33 (1998) ‘Standard Specification for Concrete Aggregates’, 05(September), pp. 98–100.

ASTM-C40 (2011) ‘Standard Test Method for Organic Impurities in Fine Aggregates for Concrete’, pp. 6–7. Available at: https://doi.org/10.1520/C0040.

ASTM C-131 (2014) ‘C131/C131M-14 Standard Test Method for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine’, Annual Book of American Society for Testing materials ASTM Standards,West Conshohocken, USA, 03, pp. 1–3. Available at: https://doi.org/10.1520/C0131.

Fatika, R.D. et al. (2023) ‘Meningkatkan Kapasitas Kuat Tekan Beton dengan Kendala Kadar Lumpur Agregat Halus’, Cived, 10(1), p. 190. Available at: https://doi.org/10.24036/cived.v10i1.121338.

Fattah, A. and Nabi, A. (2017) ‘Pengaruh zona pasir terhadap kuat tekan beton normal’, Prosiding Seminar Hasil Penelitian, 2017, pp. 107–112.

Van Gobel, F.M. (2019) ‘Nilai Kuat Tekan Beton Pada Slump Beton Tertentu’, RADIAL – jurnal peradaban saIns, rekayasa dan teknoLogi Sekolah Tinggi Teknik (STITEK) Bina Taruna Gorontalo, 5(1), pp. 22–33.

HANAFI, M.A.A. et al. (2023) ‘Efektivitas Pembuatan Beton Dengan Penggunaan Agregat Kasar Kedak’, Jurnal Riset Rekayasa Sipil, 6(2), p. 129. Available at: https://doi.org/10.20961/jrrs.v6i2.71930.

Haniza, S., Jusi, U. and Saputra, A. (2021) ‘Analisis Karakteristik Beton Self Compacting Concrete Terhadap Penambahan Superplasticizer Master Gelenium ACE 8595’, Journal of Infrastructure and Civil Engineering, 1(1), pp. 68–76. Available at: https://doi.org/10.35583/jice.v1i1.7.

Hasrudin, H., Amir, A.A. and Koten, M.T.T. (2022) ‘Studi Karakteristik Beton Menggunakan Agregat Sungai Bobong dan Agregat Sungai Gela di Kabupaten Pulau Taliabu Provinsi Maluku Utara’, Jurnal Unitek, 15(2), pp. 212–219. Available at: https://doi.org/10.52072/unitek.v15i2.449.

Hudori, M. et al. (2022) ‘Studi Pengujian Kadar Lumpur Agregat Halus Pada Pasir Di Kota Batam’, Racic : Rab Construction Research, 7(1), pp. 96–103. Available at: https://doi.org/10.36341/racic.v7i1.2536.

Husnah and Almagany, R. (2021) ‘Uji Eksperimental Penggunaan Zat Additif Mastersure 1007 Terhadap Workobility Dan Waktu Ikat Beton’, Sainstek (e-Journal), 9(1), pp. 41–46. Available at: https://doi.org/10.35583/js.v9i1.136.

Inc, G. company (2023) What is Workability of Concrete? Available at: https://www.globalgilson.com/blog/what-is-workability-of-concrete.

IS:383 (2016) ‘IS 383 (2016) :Coarse and Fine Aggregate for Concrete- Specification’, Bureau of Indian Standard, BIS, New Delhi India 110002 [Preprint].

Jhatial, A.A. et al. (2018) ‘Effectiveness of Locally Available Superplasticizers on the Workability and Strength of Concrete’, Civil Engineering Journal, 4(12), p. 2919. Available at: https://doi.org/10.28991/cej-03091208.

Keshavarz, Z. and Torkian, H. (2018) ‘Application of ANN and ANFIS Models in Determining Compressive Strength of Concrete’, Journal of Soft Computing in Civil Engineering, 2(1), pp. 62–70. Available at: https://doi.org/10.22115/SCCE.2018.51114.

Khasanov, B., Tillaev, A. and Mirzaev, T. (2021) ‘Compressive strength properties of hyper-compacted concrete’, E3S Web of Conferences, 264, pp. 1–10. Available at: https://doi.org/10.1051/e3sconf/202126402060.

Liu, J.H., Liu, X.H. and Han, W. (2012) ‘Mechanical properties test research on mass concrete mixed with different fly ash bulk volume’, Applied Mechanics and Materials, 204–208, pp. 3664–3667. Available at: https://doi.org/10.4028/www.scientific.net/AMM.204-208.3664.

Malagavelli, V. and Rao Paturu, N. (2012) ‘Strength and Workability Characteristics of Concrete by Using Different Super Plasticizers’, International Journal of Materials Engineering, 2(1), pp. 7–11. Available at: https://doi.org/10.5923/j.ijme.20120201.02.

Mark, O.G. et al. (2019) ‘Influence of Some Selected Supplementary Cementitious Materials on Workability and Compressive Strength of Concrete - A Review’, IOP Conference Series: Materials Science and Engineering, 640(1). Available at: https://doi.org/10.1088/1757-899X/640/1/012071.

Masudi, M. (2022) ‘Penggunaan Agregat Kasar Berabrasi Tinggi Pada Campuran Beton Aspal (Ac-Wearing Course) Untuk Melayani Lalu Lintas Tinggi Dengan Perbaikan Kondisi Fisik Agregat Dan Variasi Nilai Abrasi Agregat’, Seminar Nasional Insinyur Profesional (SNIP), 1(1). Available at: https://doi.org/10.23960/snip.v1i1.140.

de Matos, P.R., Sakata, R.D. and Prudêncio, L.R. (2019) ‘Eco-efficient low binder high-performance self-compacting concretes’, Construction and Building Materials, 225, pp. 941–955. Available at: https://doi.org/10.1016/j.conbuildmat.2019.07.254.

Murugesan, A. et al. (2023) ‘Compatibility matrix of superplasticizers in Ultra-High-Performance concrete for material sustainability’, Innovative Infrastructure Solutions, 8(260). Available at: https://link.springer.com/article/10.1007/s41062-023-01228-0.

Nadimalla, A.. et al. (2022) ‘Machine Learning Model to Predict Slump, VEBE and Compaction Factor of M Sand and Shredded Pet Bottles Concrete’, IOP Conference Series: Materials Science and Engineering, 1244(1), p. 012023. Available at: https://doi.org/10.1088/1757-899x/1244/1/012023.

Novan, A. et al. (2020) ‘Pengaruh Penambahan MasterGlenium ACE® 8595 dengan Pengurangan Kadar Air 37.5% dan Kadar Semen Rencana 409.80 kg/m3 Terhadap Kuat Tekan Beton’, Journal of Civil Engineering, Building and Transportation), 4(September), pp. 52–62.

Paripurna, M.T. (2019) ‘Beton dengan campuran air es dan fly ash serta retarder’, Teknika: Jurnal Sains dan Teknologi, 15(2), p. 137. Available at: https://doi.org/10.36055/tjst.v15i2.6973.

PBI (1971) ‘Peraturan Beton Bertulang Indonesia 1971’, Jakarta: Direktorat Penyelidikan Masalah Bangunan, 7, p. 130.

PUPR, D. (2005) ‘Pelaksanaan pekerjaan beton untuk jalan dan jembatan’, Badan Penelitian dan Pengembangan PUPR, pp. 1–21.

Putu, N.I. et al. (2019) ‘Tinjauan Variasi Semen Terhadap Mutu Beton Berdasarkan Kajian Sifat Kimia , Fisika , Dan Mekanik ( Metode Destructive Dan Non Destructive )’, Universitas Mataram, p. 12.

Qian, Y. et al. (2018) ‘Effect of polycarboxylate ether superplasticizer (PCE) on dynamic yield stress, thixotropy and flocculation state of fresh cement pastes in consideration of the Critical Micelle Concentration (CMC)’, Cement and Concrete Research, 107(October 2017), pp. 75–84. Available at: https://doi.org/10.1016/j.cemconres.2018.02.019.

R. Dukare, P. et al. (2013) ‘Workability of Fresh Concrete by Compacting Factor’, Civil Engineering Portal, (May), pp. 1098–1100. Available at: http://www.engineeringcivil.com/workability-of-fresh-concrete-by-compacting-factor-test.html.

Romadhon, E.S. (2021) ‘Pengaruh Lumpur Pada Pasir Terhadap Kekuatan Beton’, Jurnal Teknik Sipil-Arsitektur, 20(2), pp. 25–34. Available at: https://doi.org/10.54564/jtsa.v20i2.77.

Septianto, H. (2017) ‘Pengaruh Kandungan Lumpur pada Agregat Halus Terhadap Kuat Tekan dan Kuat Tarik Belah Beton Normal’, Doctoral dissertation, pp. 1–16.

Setiati, N.R. and Halim, H.A. (2018) ‘Pemanfaatan Semen Portland Slag Untuk Meningkatkan Sifat Mekanik dan Durabilitas Beton’, Jurnal Permukiman, 13(2), p. 77. Available at: https://doi.org/10.31815/jp.2018.13.77-89.

Shahraki, M. et al. (2023) ‘Residual compressive strength of concrete after exposure to high temperatures: A review and probabilistic models’, Fire Safety Journal, 135. Available at: https://doi.org/https://doi.org/10.1016/j.firesaf.2022.103698.

Shen, J. and Xu, Q. (2019) ‘Effect of elevated temperatures on compressive strength of concrete’, Construction and Building Materials, 229, p. 116846. Available at: https://doi.org/10.1016/j.conbuildmat.2019.116846.

Simanjuntak, J.O. et al. (2021) ‘Sifat Dan Karakteristik Campuran Beton Menggunakan Batu Pecah Dan Batu Guli Dari Sungai Binjai’, Jurnal Visi Eksakta, 2(2), pp. 239–254. Available at: https://doi.org/10.51622/eksakta.v2i2.397.

SNI-03-1968-1990 (1990) ‘Metode Pengujian Analisis Saringan Agregat Halus dan Kasar. SNI 03-1968-1990’, Bandung: Badan Standardisasi Indonesia, pp. 1–17.

SNI-03-2417-1991 (1991) ‘Keausan agregat dengan mesin abrasi los angeles’, 12(12), pp. 3–8.

SNI-03-6820-2002 (2002) ‘Sni 03-6820’, Sni 03 6820 2002, 2002, p. 6820.

SNI 03-2834-2000 (2000) ‘SNI 03-2834-2000: Tata cara pembuatan rencana campuran beton normal’, Sni 03-2834-2000, pp. 1–34.

Solikin, M. (2021) ‘Analisis Pemakaian Kombinasi Fly Ash Tipe F Dan Slag 1:1 Pada Beton Geopolymer Dengan Na2SiO3 Dan NaOH Sebagai Alkali Aktivator: Sebuah Kajian Literatur’, Dinamika Teknik Sipil: Majalah Ilmiah Teknik Sipil, 14(1), pp. 13–20. Available at: https://doi.org/10.23917/dts.v14i1.15274.

Wardi, S., Sridewi, A.K. and A., A. (2021) ‘Pengaruh Penambahan Zat Aditif Fosroc Conplast R dan Fosroc SP 337 Terhadap Kuat Tekan Beton Dengan Variasi Kadar Air’, Media Ilmiah Teknik Sipil, 10(1), pp. 10–16. Available at: https://doi.org/10.33084/mits.v10i1.2304.

Wicaksono, M.R.S. et al. (2017) ‘High stenghth concrete with high cement substitution by adding fly ash, CaCO3, silica sand, and superplasticizer’, AIP Conference Proceedings, 1818. Available at: https://doi.org/10.1063/1.4976932.

Yazid, M. et al. (2022) ‘Pengaruh Penambahan Masterglenium ACE 8595 Terhadap Kuat Tekan Beton’, Journal of Infrastructure and Civil Engineering, 2(2), pp. 106–113. Available at: https://doi.org/10.35583/jice.v2i2.22.

Zhang, L. et al. (2018) ‘Working mechanism of post-acting polycarboxylate superplasticizers containing acrylate segments’, Journal of Applied Polymer Science, 135(5), pp. 1–13. Available at: https://doi.org/10.1002/app.45753.